TEGARA 6 690X CNC Milling Machine Vise No Swivel Base NEW R

TEGARA 6 690X CNC Milling Machine Vise No Swivel Base NEW. JAW PLATE THREADS SPACING (INCH). Tegara's new CNC Milling Vise has just put the squeeze on the competition. How'd they do it? Simple -- by making theirs hands-down a cut above the other ones. It just works better, is easier to use, and lasts longer. And that's what it's all about. So why is their new 690X vise able to stand up to the abuse of even the most demanding machine shops and still do what it's supposed to do? It's not just hard, it's 80,000 PSI stress relieved ductile-cast iron hard. You can say goodbye to worrying about "Jaw Lift" because that threat is virtually gone. Of clamping force guarantees what you clamp stays clamped. All that the clamping force is pulled, not pushed, to reduce stress and minimize deflection.

2 large chip evacuation slots are perfectly located to get that stuff out of your way and keep it out. It does more with less, having a bigger capacity but a smaller footprint than previous generation vises. And those are just some of the reasons this vise rules. Big picture, all critical components have been precision turned to achieve smooth but rigid movement.

You can feel the power right there in your hands. So go ahead, put it through its paces. Lock it down and give it a go. Put it through the ringer and you find out that it was made to take a beating and emerge battle-tested and victorious.

Tegara has set a new standard in precision machine vises with the 690X. And the best and most important thing to know about this CNC Milling Machine Vise? A gang of vise body gone through time consuming grinding process with micron accuracy on a CNC grinder.

Each vise body will be put under the microscope to filter out unsatisfying cast iron bodies before assembling. Semi-hardened bright finished lead screws with precision turned threads to give them a solid & smooth feel when turning the vise handle. With a heavy duty thrust bearing pack located on the rear of the vise body, the clamping force is a pulled rather than pushed motion. This pulling mechanism would reduce stress and minimize deflection on the vise body when applying high clamping pressure. Besides the integrated key on the stationary jaws, 4 additional solid cap screws are bolted down from the top to increase holding strength and prevent jaw lift.

An recessed cavity is created on the back of the jaw for easier lifting. Every machinist is afraid of the term "jaw lift" when associated with a vise. The 690X offers key improvements to prevent jaw lifting by using a 45 degree wedge and a pivoting ground finished steel hemisphere in a milled pocket to hold down the movable jaw.

This results a minimal amount of jaw lift applying under pressure when comparing to other highly regarded go-to branded vises. 9.10" Opening capacity compared to the 8.89" from previous generation 690V vises, the 690X offers a larger capacity with a smaller foot print. The base of vise body is only 7.32" wide as opposed to the 8.75" from 690V series. With the 4 mounting thru holes with 4 spacing on the vise bed would allow more vises mounting side by side on a milling table.

Hardened Vise Bed / Jaw Plate. Vise jaw plate threads and spacing meets the industry standards - Bedways are flame hardened to 45 HRc and jaw plate hardened to 54 HRc - Bed height and the distance between keyway and stationary jaw remains the same and meets the industry standards - Bed height matched to 2.875" +/- 0.0005" - Vises' bed parallel to base within 0.0005" - Fixed Jaw perpendicular to bed within 0.0005" - Fixed jaw parallel to vise's keyway within +/- 0.0005.

Continuing from the design feature in 690V vises, a brush on both end of spindle nut to wipe off chips to improve & extend the lead screw life. 2 large chip evacuation slots are strategically located on each side of the vise to allow a good flow of chips while at the same time not diminishing the vise's body strength. The vise body is also reinforced with a thicker rib to support the pulling mechanism when clamping.

When ordering multiple vises, the bed heights will be matched within. 0001 at no additional cost (subject to inventory stock availability). (The life of the product or part is defined as that point in time when such item no longer functions due to normal wear and tear). Vise Nut and Brush Pair. 2 pc of 11/16 T-slot Keys.

12.5" W x 8" H Polycarbonate Chip Guard for 5" & 6" Vise.