SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New

SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New

SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New

SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base NEW. USE ON NC/CNC MACHINES FOR CUSTOMER WHO ONLY NEEDS ONE VISE NOT TWO OR MORE, BECAUSE OF BED HEIGHT TOLERANCE , THESE VISES CAN'T BE USED TOGETHER. Accurate to 0.002 per 4 on squareness and 0.006 per 4 on parallelism without base. Vise Key: 15.875mm table slot width, 18.00mm base width. Each pound of force in horizontal induces 1/2 lb of downward force, eliminating jaw tilt.

This Vise is so designed that the horizontal force generated by tightening the handle pushes the semi-sphere within the movable jaw and thus thrusts the movable jaw downward. The workplace does not move up, even if it is held at the top of the jaw plates. It's very accurate and durable. Sliding surface of the vise bed is flame hardened and ground. Made from the highest quality ductile Iron 80000 PSI for minimum bending. K type angle lock nut is made from the highest quality ductile Iron, firm and durable. Acme screws and easy to read 0-360 deg scales. Screws from the top through the jaw make the vise more stable and durable. The installation size of Soft Jaw is the same as Kurt.

6 Aluminum Soft Jaws which are made in USA can be mounted into this vise. Four setting positions of the jaw plates are available, widening the jaw plates opening.

Four ways to use the vise, shows on the following fig. Jaw Plate Bolt Hole Spacing: 3.875'. When A and C are unequal to E, you can swivel the vise base to suitable angle.

Then the vise can be installed onto the Mill. SHARS 4 440V Milling Vise +/-0.0004.

4" wide jaw plate, 4" inner jaw opening, 10 outer jaw opening. Made from 80,000PSI stress relief cast iron. Vise bed hardened to 45 HRc and jaw plate hardened to 54 HRc.

Bed height Tolerance 2.25" +/-0.0005". SHARS 6 670V Milling Vise +/-0.0004. 6" wide jaw plate, 8.95" inner jaw opening, 17 outer jaw opening.

Bed height Tolerance 2.875" +/-0.0005". SHARS 6 660U Milling Vise +/-0.0004. 6" wide jaw plate, 6.25" inner jaw opening, 15 outer jaw opening. Single piece of stationary jaw and vise body to enhance clamping rigidness and accuracy. Bed height Tolerance 3.189" +/-0.0005".

SHARS 6 600DS Double Station Milling Vise +/-0.0002. 4.9" jaw opening in double station, 12" jaw opening in single station (conversion kit included).

Unique leadscrew design to allow to clamp either same sized or dissimilar sized parts. Jaw lift prevention mechanism by eccentric pin design. Bed height Tolerance 3.25" +/-0.0005" (matched bed height at no additional cost).

The item "SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New" is in sale since Wednesday, April 13, 2011. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Workholding & Toolholding\Workholding\Vises". The seller is "discount_machine" and is located in Saint Charles, Illinois.

This item can be shipped to United States, Canada.
SHARS 6 x 7-1/2 Precision Mill Vise Anti-Jaw Lifting With Swivel Base New